Force effects: In the cutting process, the blade subject to axial force
and tangential force. Because there is in the circumferential direction
and the radial force, in the axial direction so wet granite pads that the blade wavy dish
in radial direction. Both can cause deformation of the rock section is
not flat, stone wasted, sawing noise, vibration intensified, resulting
in diamond caking early damage, reduced blade life.
Temperature effect: the traditional theory: the influence of temperature
on the blade process is mainly manifested in two aspects: First, cause
agglomeration of diamond graphitization; two diamond and matrix is
caused by thermal stress caused by premature loss of diamond particles.
New research showed that: the heat generated during cutting the main
incoming agglomeration. Arc temperature is not high, generally between
40 ~ 120 ℃. The abrasive grinding point temperature was high, generally
between 250 ~ 700 ℃. The coolant only reduce the average temperature of
the arc zone, the temperature has little effect on the grain. This does
not result in graphite carbonization temperature, but will make the
friction between the abrasive particles and the workpiece change in
properties, and to occur between 12 inch saw blade the diamond and the additive thermal
stress, which led to fundamental changes in the failure mechanism of
diamond. Studies have shown that the temperature effect is to make the
biggest factors blade breakage.
Grinding damage: the force effects and temperature than the response,
after a period of use of the blade tend to produce wear damage. Grinding
damage in the form of mainly the following: abrasive wear, local
crushing, a large area of broken off, binders direction along the
cutting speed of the mechanical abrasions. Abrasive: Diamond particles
and constant friction formula pieces, into a flat edge passivation, loss
cutting, increasing friction. Heat causes the cutting surface of the
diamond particles graphite sheet, the hardness greatly reduced,
increased wear: the surface of the diamond particles exposed to
alternating thermal stresses, and also diamond tool manufacturer the cutting under alternating
stress, fatigue cracks will be partially broken, revealing a sharp new
edge, is an ideal wear pattern; large area broken: diamond particles in
the Leads to withstand shock loads, the more prominent grain and grain
prematurely consumed; shedding: the diamond cutting force alternating
binding agent particles are constantly being generated shaking loose.
Meanwhile, the cutting process of the binding agent itself wear and
cutting heat to soften the binding agent. This makes the gripping force
decreased binding agent, when the particle is greater than the cutting
force on the gripping force, the diamond particles will fall off. No
matter what kind of wear and tear with the diamond particles to
withstand load and temperature are closely related. Both of which are
determined by sawing process and cooling lubrication conditions.
diamond core drills, not only in geological exploration has an important position, but also because it has got speed, stone loss, does not destroy the surrounding environment and other unique advantages and is widely used in marble, granite, reinforced concrete walls of the drill hole
PCD grinding wheel
2013年10月21日星期一
2013年10月11日星期五
Carbide saw blade manufacturing companies can not do so many specifications of the saw blade
according to law and according to the current preferred wood processing enterprises in the equipment, materials and concrete diamond blades other specific factors that make up the specifications currently used carbide saw blade series. This helps us use carbide saw blades, but also conducive alloy blade manufacturing enterprise scale production.
Under normal circumstances, sawing particleboard, medium density board should be selected so teeth, sawing plywood, fire board generally choose Ladder tooth (flat tooth, trapezoidal tooth combination). Depending on polishing pads the diameter of the blade circular sawing machine model to Ф300-350mm majority, saw blade thickness and diameter. Ф250-300mm thickness 3.2mm, Ф350mm than 3.5mm.
Since computer saws saws honestly rate, with a carbide blade diameter and thickness of the relatively large, about 350-450mm in diameter, thickness 4.0-4.8mm between, the majority of flat construction tools ladder teeth to reduce chipping , saw marks.
Alloy saw blade sawing wood is usually combined into Dou about tooth teeth, because this combination before the angle, can sharply cut the wood fiber tissue, clean cut. For slotted flat bottom to keep it, use flat teeth tooth or teeth with left-right combinations.
Under normal circumstances, sawing particleboard, medium density board should be selected so teeth, sawing plywood, fire board generally choose Ladder tooth (flat tooth, trapezoidal tooth combination). Depending on polishing pads the diameter of the blade circular sawing machine model to Ф300-350mm majority, saw blade thickness and diameter. Ф250-300mm thickness 3.2mm, Ф350mm than 3.5mm.
Since computer saws saws honestly rate, with a carbide blade diameter and thickness of the relatively large, about 350-450mm in diameter, thickness 4.0-4.8mm between, the majority of flat construction tools ladder teeth to reduce chipping , saw marks.
Alloy saw blade sawing wood is usually combined into Dou about tooth teeth, because this combination before the angle, can sharply cut the wood fiber tissue, clean cut. For slotted flat bottom to keep it, use flat teeth tooth or teeth with left-right combinations.
steel blade quenching process
The main part of diamond saw blade is circular thin iron, stone cutting high hardness, if you saw the matrix strength and metal grinding wheel hardness is not high enough, it may be side blade-shaped, therefore, how to improve the strength of steel , is to ensure the quality of one of the main blade.
Matrix forming the blade after quenching to the billet processing, then what is the quench it? The billet is heated to a temperature of sub-eutectoid steel or eutectoid steel above a certain temperature, holding time, it would be all of the austenite one, and then quickly cooled to ring saw blades a temperature Ms less (or Ms near isothermal) for martensite (or bainite) transformation, this process is called quenching. Objects can greatly improve the strength of steel, the hardness and wear resistance. Therefore, when machining the blade billet, is an essential step of quenching.Diamond saw blades in China's rapid economic development in the use of more extensive, involving industry stone processing enterprises, especially in the real estate industry, decoration processing must frequently use, this article describes the diamond core drills classification and use of diamond saw blade shape occasion. Because, according to appearance can easily be classified, there are these types: 1, head-type blades, serrated because it is disconnected two consecutive edges of the blade; diamond saw blade according to the above three points is the shape of the classification. 3, a turbine blade type, as it is a sawtooth-shaped turbine.
Matrix forming the blade after quenching to the billet processing, then what is the quench it? The billet is heated to a temperature of sub-eutectoid steel or eutectoid steel above a certain temperature, holding time, it would be all of the austenite one, and then quickly cooled to ring saw blades a temperature Ms less (or Ms near isothermal) for martensite (or bainite) transformation, this process is called quenching. Objects can greatly improve the strength of steel, the hardness and wear resistance. Therefore, when machining the blade billet, is an essential step of quenching.Diamond saw blades in China's rapid economic development in the use of more extensive, involving industry stone processing enterprises, especially in the real estate industry, decoration processing must frequently use, this article describes the diamond core drills classification and use of diamond saw blade shape occasion. Because, according to appearance can easily be classified, there are these types: 1, head-type blades, serrated because it is disconnected two consecutive edges of the blade; diamond saw blade according to the above three points is the shape of the classification. 3, a turbine blade type, as it is a sawtooth-shaped turbine.
2013年10月10日星期四
Electroplated diamond grinding wheel defects exist
Electroplated diamond grinding wheel defects exist :
1 , using a large positive rake angle machining, tool wear serious , cutting vibration is large, and the substrate and diamomd core drill bits the coating metal surfaces are not kept firmly binding the abrasive chemical metallurgical bonding , actually only be mechanically entrapped abrasive coating metal mosaic , thus dominated force is small ;
2, the diamond particles heavier load efficiency, for processing efficiency, processing quality , processing costs, and a great influence on the grinding tool life easy to fall off ( or plating flaking ) and lead to an overall failure ;
3 , to increase the holding force Edge 2000 Pads must be increased coating thickness , and the results highly abrasive bare chip space is reduced, wheel prone to clogging , the cooling effect is poor, prone to burn the workpiece surface ;
4 , the current domestic electroplated grinding wheel manufacturing has not been achieved by optimized processing conditions required to design the best grinding wheel topography, in the domestic diamond coating technology is still in its infancy , as well as the cost of diamond cbn wheel inputs are big , so in the near future diamond coating there is not much development ;
5, the tool angle change on the tool wear, cutting force and cutting vibration is rake angle , clearance angle and helix angle integrated generated , so the choice we must pay more attention to single-layer electroplated diamond grinding wheel will be significantly restricted these inherent drawbacks its efficient grinding applications .
1 , using a large positive rake angle machining, tool wear serious , cutting vibration is large, and the substrate and diamomd core drill bits the coating metal surfaces are not kept firmly binding the abrasive chemical metallurgical bonding , actually only be mechanically entrapped abrasive coating metal mosaic , thus dominated force is small ;
2, the diamond particles heavier load efficiency, for processing efficiency, processing quality , processing costs, and a great influence on the grinding tool life easy to fall off ( or plating flaking ) and lead to an overall failure ;
3 , to increase the holding force Edge 2000 Pads must be increased coating thickness , and the results highly abrasive bare chip space is reduced, wheel prone to clogging , the cooling effect is poor, prone to burn the workpiece surface ;
4 , the current domestic electroplated grinding wheel manufacturing has not been achieved by optimized processing conditions required to design the best grinding wheel topography, in the domestic diamond coating technology is still in its infancy , as well as the cost of diamond cbn wheel inputs are big , so in the near future diamond coating there is not much development ;
5, the tool angle change on the tool wear, cutting force and cutting vibration is rake angle , clearance angle and helix angle integrated generated , so the choice we must pay more attention to single-layer electroplated diamond grinding wheel will be significantly restricted these inherent drawbacks its efficient grinding applications .
Grinding wheel burns and their solutions
In view of the workpiece during grinding wheel burns has been plagued by product quality problems, grinding performance, good surface quality . As CBN abrasive grains can be maintained long-term micro- edge sharpness , will make the workpiece machining accuracy and surface roughness values are achieved more satisfactory results , thus allowing the iamond saw blade workpiece durability increased by 10 % -30 % . Therefore, even if the batch processing of the workpiece, will always get a high shape accuracy and consistency. Grinding wheel burns from the formation mechanism , wheel grinding burn method of examination , grading wheel grinding burn , burn measures to avoid grinding wheel , grinding wheel burn factors , grinding wheel burns solution. Chemical inertness . Cubic boron nitride and iron group elements is dry bits not easy to produce a chemical reaction , so for a variety of high-speed steel , tool steel , tool steel, high alloy hardened steel , chromium steel, nickel alloys , powder metallurgy steel and high temperature alloys such as high temperature , high hardness , low thermal conductivity of the material is very suitable for grinding . Let's start with basic understanding of the formation of the grinding wheel grinding burn to burn on the grinding wheel to form a complete set of solutions to plan , in which: the choice of the grinding wheel grinding wheel burn process is very important . We produce in order to avoid to avoid burns, burns encountered while to find a reasonable solution . Cost savings , high deposition rate , high wear diamond cup grinding wheel resistance, high corrosion resistance. Not only to improve the current efficiency , but also increases the wear resistance and corrosion resistance. Applied to any hard chrome plated , including ; microcracks chrome , white chrome , shiny chrome , etc. can also be used . Good quality , process stability , high efficiency , energy conservation, significant economic benefits. For cylindrical grinding burns, internal grinding burns, burns flat grinding , face grinding burns, burns , etc. centerless grinding wheel grinding way . Diamond resin grinding wheel has a good polishing effect , grinding wheel sharp , easy to plug .
2013年10月9日星期三
diamond segment of the optical properties of diamond
(1) The brightness of the optical identification (Brilliance) because of the diamond has a very high reflectivity of the reflection critical angle is small, a wide range of total reflection, total 14 inch saw blade reflection light is easily reflected light is large, resulting in high brightness.
(2) Flashing (Scintillation) is flashing diamond flash, that is, when the diamond or the light source, the observer moves relative to the surface of the white light reflection and flash. Colorless, transparent, well-crystallized poly octahedral shaped diamond surface bodies or, if not Gache grinding can expose good flashing light.Depends not only on the diamond bandsaw blades performance of the blade diamond, but on the diamond and the binder with the appropriate head of this composite material composed of the overall performance. For marble and other soft stone, head of the mechanical properties required is relatively low, the choice of copper-based binder. The sintering temperature is low but the copper-based binder, strength, low hardness, high toughness, low bonding strength with the diamond. When adding tungsten carbide (WC), the WC or W2C to as a skeleton metal, with the amount of cobalt in order to improve the strength
(3) the dispersion or the wet granite pads fire (Dispersion or fire) planes of diamond as diverse as prism, can through refraction, reflection and total reflection into the interior of the crystal composition of white light into white color - red, orange, yellow, green, blue, indigo, violet shade.
(4) Gloss (Luster) outstanding diamond-like hard, smooth and bright crystal face or cleavage face in white light reflection effect particularly strong, and this is very characteristic of the role of reflective called adamantine luster.
(2) Flashing (Scintillation) is flashing diamond flash, that is, when the diamond or the light source, the observer moves relative to the surface of the white light reflection and flash. Colorless, transparent, well-crystallized poly octahedral shaped diamond surface bodies or, if not Gache grinding can expose good flashing light.Depends not only on the diamond bandsaw blades performance of the blade diamond, but on the diamond and the binder with the appropriate head of this composite material composed of the overall performance. For marble and other soft stone, head of the mechanical properties required is relatively low, the choice of copper-based binder. The sintering temperature is low but the copper-based binder, strength, low hardness, high toughness, low bonding strength with the diamond. When adding tungsten carbide (WC), the WC or W2C to as a skeleton metal, with the amount of cobalt in order to improve the strength
(3) the dispersion or the wet granite pads fire (Dispersion or fire) planes of diamond as diverse as prism, can through refraction, reflection and total reflection into the interior of the crystal composition of white light into white color - red, orange, yellow, green, blue, indigo, violet shade.
(4) Gloss (Luster) outstanding diamond-like hard, smooth and bright crystal face or cleavage face in white light reflection effect particularly strong, and this is very characteristic of the role of reflective called adamantine luster.
How to determine the level of diamond saw blades
In general, diamond saw blade working environment is bad, products are mainly used for sawing stone, widely used in marble, granite, ceramic tiles and concrete products for cutting, is stone, building industrial saw blades materials industry, an important and widely used processing tools.
Circular saw blades cutting with easy operation, high efficiency, good processing quality and other advantages. But noisy, blade rigidity. Easy to produce during cutting blade runout, deviation, resulting in the parallelism of the workpiece to be cut is poor. Saw cutting spindle bear a large force, the swing generated during the cutting, but not cut out straight, the blade thickness can be increased despite increased rigidity, it is diamond polishing tools still difficult to ensure parallelism of the slice. In addition, the increased thickness of the blade not only increases costs, but also increases the kerf width reduces the volume ratio. Cylindrical cutting line speed is higher, up to 50m / s, the diameter of the saw blade cutting depth by limiting, usually less than the diameter of the third. Currently, the cutting depth is generally not more than 1 meter. The carbide drill bits most critical quality diamond saw blade with diamond granularity necessary, which is testing the wear resistance of diamond saw blades and sharp the most important indicators.
Circular saw blades cutting with easy operation, high efficiency, good processing quality and other advantages. But noisy, blade rigidity. Easy to produce during cutting blade runout, deviation, resulting in the parallelism of the workpiece to be cut is poor. Saw cutting spindle bear a large force, the swing generated during the cutting, but not cut out straight, the blade thickness can be increased despite increased rigidity, it is diamond polishing tools still difficult to ensure parallelism of the slice. In addition, the increased thickness of the blade not only increases costs, but also increases the kerf width reduces the volume ratio. Cylindrical cutting line speed is higher, up to 50m / s, the diameter of the saw blade cutting depth by limiting, usually less than the diameter of the third. Currently, the cutting depth is generally not more than 1 meter. The carbide drill bits most critical quality diamond saw blade with diamond granularity necessary, which is testing the wear resistance of diamond saw blades and sharp the most important indicators.
订阅:
博文 (Atom)